Ppjoy Joystick Driver 0.8 4.5 Download Install Update
Discussion about PPJoy ideas and updates on development progress. Thank you for all your work. I'm a have a bit of a security paranoia, so i don't like to be in test mode, but other than that it worked perfectly. The newer version installs itself fine, but still I can't get the mouse controll work. The controller is in the game devices, but it doesn't respond to the movement or anything with GlovePIE.
What shall I do? I know this isn't topic of this blog, but don't know where the hell i can talk about NES wiring in the internet I found this modified scheme http: Also VD7,8 protect scheme. Perhaps VD, pins , will be enough to power 2 nes pads? I finally found what was my problem. This comment has been removed by a blog administrator.
W7 64bit works like a charm! That would be just great for my old tie fighter game: Got it working thanks to this post: Install PPJoy obvious 2. Start GlovePIE, open script file, run it.
I have a few issues with my genesis pad I think this is all a problem with ppjoy. The xyz buttons press themselves but only on the emulators and other programs, in the joystick section of the control panel it works fine. The only solution i find to this problem is to use joytokey but with newer version of Mame it doesnt work. Is there a way of taking windows out of test mode, but continuing to be able to use PPJoy in Windows 7 x Is there a way of allowing the driver to be used in normal windows mode?
Does this program work with pci parallel adapters or only built in parallel ports? I ask this because I believe I have the program properly installed running 64 bit windows 7. Ran in test mode installed successfully. But whenever i try to setup my playstation pad the mapping and timing functions give me the error: This has persisted through multiple re-installs as well.
USB parallel ports will not work. Have you tried running the control pnael applet as administrator? Might make a big difference. PPJoy uses test signed drivers and thus Windows x64 needs to be in test mode else the drivers won't load. Buying the proper certificates costs a few hundred dollars. I could possibly add a feature to centre the joystick if no trachball movement after x seconds.
Is the trackball seen as a mouse? Do you use PPJoyMouse with it? But i can't get Windows 7 to enter Test mode either. I keep getting this error in the prompt: Microsoft Windows [Version 6.
So how do I get it to work? Just to add, I am in the main Administrator account I am getting a File not found error for the link you gave. I enter it and then I get a The link is dead, i can't dload it, would u re upload it pls? Here's a few mirrors: I wanted to report my problem or bug. Sometimes when I press the arrow buttons on my sega genesis gamepad, the game character throws kicks and fists.
But I never pressed the buttons of fists or kicks. This happens with all games for Zsnes and Kega Fusion emulators, but this error never happens with other emulators like snes9x or native games for windows. I only found problems with these emulators, which are the best and I use them frequently. Info on my system: Ok all eight buttons and directional.
Excuseme for possible translation errors, since I speak Spanish. Thanks in advance for any answers or help and greetings to all from Argentina. With the release of Mechwarrior4Free, I think a lot of Windows7 users are going to want to get a hold of this product if they are using the Logitech G, which shows up as 3 separate devices in Windows and the game which means if you want to use the throttle or pedals you'll only be able to assign them to keystrokes rather than analog axes.
Any chance you could post the latest version on something other than dropio you've exceeded downloads? I developed many Windows and Linux drivers and I know this hard job.
Can you help me? I have the same configuration in Windows XP e everthing works fine I downloaded the file via http: I've took the oportunity to re-upload it again. I cannot download the release from glovepie and can't find this anywhere else, can someone please rehost?? This is a extremely nice contribution just as getting Viagra Online.
Is it really the trojan or it is just MacAfee? Ooh man, that was tough, After some research I understood that this is still MacAfee. So I took the risk and disabled virus check for those specific files. But driver is still unsigned: It seems that Windows updated their security since driver release. So i looked on Internet a bit more and found the way how to sign drivers. Here is the manual I followed: Driver Signature Enforcement Overrider 1. I think this is part of its heuristic to mark all suspicious activity in Windows folder.
So I had to add 2 more exceptions to its rules: I don't know if all these actions were indeed needed or I was so "lucky". This works fine on an old desktop I have with a real parallel port, but that computer can't run modern emulators.
Is there a way to get PPJoy to look for this the way it would look for 0x? Ok, I've just re-uploaded 0. Also, here's a MegaUpload link  and a 4shared link.
Both have been uploaded by me. Again, here goes the MD5 Hash: Thank you very much for your ppjoy development! I have installed 8. But I do not have any joysticks visible in control panel. And here I must be missing some important step, what to do next. They both do not see anything. Any hints are appreciated.
Deon can u reupload PPJoy 64bit All what i found with viruses. Reup please - all Mirrors here are Infected. Yes, please upload a clean version. Every single one I've found is infected. Maybe get CNet to host one? This makes life difficult for those of us who use PPjoy to combine several real joysticks into one virtual one. Wow I was just about to write the same thing as Dave. I've done my best to force the virtual joystick to have another VID in order to get a game to work properly.
The game only recognizes the first 4 controllers so when I try to map 4 steering wheels to PPJoy I'm out of luck. It really fills a gap I've had for a long time when it comes to remapping joystick buttons. If only I could get the virtual joysticks to show up at the top of the list I could get PPJoy working with all of my games. There is no trojan.
Your anti-virus programs are giving you false alarms. Install a better one such as Avast or Kaspersky. Hi, nothing exists to take midi controllers as game controllers why not add it in PPJoy?
Advanced Uninstaller PRO
PPJoy Joystick Driver 0. This page holds details on how to remove it from your computer. It was created for Windows by Deon van der Westhuysen. Further information on Deon van der Westhuysen can be seen here. The program is often placed in the C: The program's main executable file has a size of After the uninstall process, the application leaves some files behind on the computer. Some of these are listed below. Some users try to uninstall this application. This is easier said than done because performing this manually requires some advanced knowledge regarding PCs.
Discussion about PPJoy ideas and updates on development progress. Thank you for all your work. I'm a have a bit of a security paranoia, so i don't like to be in test mode, but other than that it worked perfectly. The newer version installs itself fine, but still I can't get the mouse controll work. The controller is in the game devices, but it doesn't respond to the movement or anything with GlovePIE. What shall I do? I know this isn't topic of this blog, but don't know where the hell i can talk about NES wiring in the internet I found this modified scheme http: Also VD7,8 protect scheme. Perhaps VD, pins , will be enough to power 2 nes pads? I finally found what was my problem.