Ga 945gcm S2l Audio Driver Download Latest

By Matthew

Ga 945gcm S2l Audio Driver Download Install Update

Support for Download Center The trademarks mentioned in this manual are legally registered to their respective owners. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

For product-related information, check on our website at: Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.

Table of Contents Box Contents The box contents are subject to change without notice. Optional Items 2-port USB 2. Prior to installation, carefully read the user's manual and follow these procedures: These stickers are required for warranty validation. Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely. When handling the motherboard, avoid touching any metal leads or connectors. It is best to wear an electrostatic discharge ESD wrist strap when handling electronic components such as a motherboard, CPU or memory.

If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity. Prior to installing the motherboard, please have it on top of an antistatic pad or within a electrostatic shielding container. Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.

Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard. To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components. Do not place the computer system on an uneven surface.

Do not place the computer system in a high-temperature environment. If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. Note 4 Available functions in Easytune may differ by motherboard model. The CPU cannot be inserted if oriented incorrectly. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals.

If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. Hyper-Threading Technology System Requirements: Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.

Completely raise the CPU socket lever. Lift the metal load plate from the CPU socket. DO NOT touch socket contacts. Remove the protective socket cover from the load plate. Hold the CPU with your thumb and index fingers. Once the CPU is properly inserted, replace the load plate and push the CPU socket lever back into its locked position.

Apply an even and thin layer of thermal grease on the surface of the installed CPU. Before installing the cooler, note the direction of the arrow sign on the male push pin. Turning the push pin along the direction of arrow is to remove the cooler, on the contrary, is to install. Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard.

Push down on the push pins diagonally. You should hear a "click" when pushing down each push pin. Check that the Male and Female push pins are joined closely. Refer to your CPU cooler installation manual for instructions on installing the cooler.

After the installation, check the back of the motherboard. If the push pin is inserted as the picture above, the installation is complete. It is recommended that memory of the same capacity, brand, speed, and chips be used. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth.

Dual Channel mode cannot be enabled if only one DDR2 memory module is installed. When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used. Follow the steps below to correctly install your memory modules in the memory sockets. Note the orientation of the memory module. Spread the retaining clips at both ends of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket.

The clips at both ends of the socket will snap into place when the memory module is securely inserted. Carefully read the manual that came with your expansion card. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.

Align the card with the slot, and press down on the card until it is fully seated in the slot. Make sure the metal contacts on the card are completely inserted into the slot. Secure the card's metal bracket to the chassis back panel with a screw. After installing all expansion cards, replace the chassis cover s. Turn on your computer. Install the driver provided with the expansion card in your operating system. Gently push down on the top edge of the card until it is fully inserted into the PCI Express x16 slot.

Make sure the card is securely seated in the slot and does not rock. Gently push back on the lever on the slot and then lift the card straight out from the slot. Parallel Port Use the parallel port to connect devices such as a printer, scanner and etc. The parallel port is also called a printer port.

Serial Port Use the serial port to connect devices such as a mouse, modem or other peripherals. Connect a monitor that supports D-Sub connection to this port. Do not rock it side to side to prevent an electrical short inside the cable connector. Use this audio jack for line in devices such as an optical drive, walkman, etc. Line Out Jack Green The default line out jack. Use this audio jack for a headphone or 2-channel speaker. Microphones must be connected to this jack. Unplug the power cord from the power outlet to prevent damage to the devices.

Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start. If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

When using a 2x12 power supply, remove the protective cover from the main power connector on the motherboard. Do not insert the power supply cable into pins under the protective cover when using a 2x10 power supply. When connecting a fan cable, be sure to connect it in the correct orientation. Most fans are designed with color-coded power connector wires.

The black connector wire is the ground wire. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. Overheating may result in damage to the CPU or the system may hang. Do not place a jumper cap on the headers. The types of floppy disk drives supported are: Before connecting a floppy disk drive, be sure to locate pin 1 of the connector and the floppy disk drive cable. The pin 1 of the cable is typically designated by a stripe of different color.

Before attaching the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices, remember to set the jumpers and the cabling according to the role of the IDE devices for example, master or slave. The LED is on when the system is operating.

Ga 945gcm S2l Audio Driver Download

Gigabyte GA-945GCM-S2L Motherboard Drivers

Page 81 Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product where applicable , recycling the inner and outer packaging including shipping containers this product was delivered in, and by disposing of or recycling used batteries properly. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. Driver CD Information This page provides information about the drivers, applications and tools in this driver disk. The procedure is complete after the system restarts. You will be requested to confirm the password. Please note that if there is no enough unallocated space, Xpress Recovery2 cannot save the backup file. BIOS will emit warning sound. Page 84 All specifications and figures are subject to change without notice.

GIGABYTE SOCKET 775 GA-945GCM-S2L

Ga 945gcm S2l Audio Driver Download

You can see device drivers for a Gigabyte Motherboards below on this page. Motherboard drivers are a kind of software, and therefore they are subject to all the same problems that affect the work of other kinds of programs. Keep in mind that motherboard drivers may also be damaged for various reasons, such as virus-infected, or obsolete as a result of system upgrades or software changes. Remember that is very important to have exactly the driver that is needed specifically for your hardware motherboard model. Therefore, it is recommended that you search using the motherboard manufacturer name and model number of each motherboard. Most popular Gigabyte Motherboards: Realtek High Definition Audio Driver. Realtek Ethernet Diagnostic Utility. Intel Graphics Media Accelerator Driver.

0 thoughts on “Ga 945gcm S2l Audio Driver Download

Leave a Reply

Your email address will not be published. Required fields are marked *